32oz Foam Solution – Pour & Go

✦ Who Should Buy Pour & Go Packs?

• First-Time Foam Party Hosts — Never mixed foam solution before? Pour & Go removes every possible mistake. No ratios to calculate, no concentrate to measure, no breakdown steps, no rest time. Pour the pack in, add water, done. If your first foam event goes well, you can graduate to larger-format solutions like Ready to Run or Gel for better per-gallon economics.
• One-Off & Casual Events — Hosting a single birthday party, backyard gathering, or neighborhood event? You don't need a gallon of concentrate or a bulk bag of powder. You need enough solution for one or two barrel fills and zero leftover product. Pour & Go Packs are right-sized for small, casual events.
• Rental Customers & Machine Borrowers — Renting a foam machine from a friend, event company, or venue? Pour & Go means the person running the machine doesn't need any foam experience. Hand them the pack and say "pour this in, fill with water, turn it on." That's the entire instruction set.
• Operators Stocking for Rental Clients — If you rent out foam machines, Pour & Go Packs are the ideal solution to include with the rental. Your clients get foolproof solution that eliminates support calls about mixing ratios, and you can sell the packs as an add-on to each rental.
• Quick Demo & Test Runs — Need to test a foam machine, demo for a client, or verify your setup before an event? A single Pour & Go Pack gets you 20 gallons of solution for a quick run without opening a gallon of concentrate.
• Emergency Backup — Keep a few packs in your gear case as backup. If you run through your primary solution faster than expected or discover a mixing problem on-site, a Pour & Go Pack gets you a fresh 20 gallons of solution in under a minute with zero measuring.

📋 Specifications

What's In It

The same cosmetic-grade surfactant blend used in every SurgeFX foam solution — organic, all-natural foaming agents that produce foam consisting of approximately 99% air and water. No detergents, degreasers, cleaning chemicals, dyes, or artificial fragrances. The only difference between Pour & Go and other SurgeFX solution formats is the packaging and concentration — the chemistry is identical.

Safety Profile

Hypoallergenic. Neutral pH. Biodegradable. Non-staining. Safe for direct skin contact in adults, children, and pets. Avoid direct eye contact — foam solution can cause temporary eye irritation (same as shampoo or bubble bath). Not a food product — do not ingest. Rinse off after extended skin contact.

🔧 How to Use — Three Steps

This is the entire process:

• 1. Pour — Empty the entire 32 oz pack into your mixing barrel or container.
• 2. Fill — Add water to approximately 20 gallons. A standard 53-gallon barrel filled to roughly the 40% mark is about right. A garden hose works fine.
• 3. Run — Connect your foam machine and go. No stirring required, no rest time, no waiting. The concentrate disperses as the barrel fills with water.

That's it. No measuring cups, no calculators, no ratio charts. The pack is premixed at the correct concentration — pouring the full 32 oz into 20 gallons of water produces the right solution strength automatically.

Adding Color, Scent, or UV

Want colored, scented, or UV-reactive foam? After pouring the Pour & Go pack and filling with water, add your Foam Color Additive, Scented Solution, or UV Glow Powder to the barrel and stir briefly to distribute. Always add additives after the base solution is mixed — never to the pack itself.

⚖ Pour & Go vs. Other Solution Formats

SurgeFX offers foam solution in multiple formats. Pour & Go is the simplest and most beginner-friendly. Here's how it compares:

When to Choose Pour & Go

Choose Pour & Go when simplicity is the priority. You're hosting your first foam event and don't want to deal with measuring or ratios. You're sending solution with a rental client who has zero foam experience. You need a quick demo or test run. You want emergency backup packs in your gear case. Pour & Go costs more per gallon of yield than larger formats, but it eliminates every mixing variable in exchange.

When to Upgrade

Once you're comfortable with the foam process and running events regularly, stepping up to Ready to Run (1 Gallon) gives you significantly more yield per dollar — one gallon treats approximately 75 gallons of water vs. Pour & Go's 20 gallons per 32 oz. For maximum economy, Gel Concentrate treats 400 gallons per gallon (with a 24-hour breakdown step). Pour & Go is the on-ramp. The other formats are where you go once you know what you're doing.

❓ Frequently Asked Questions

How much foam does one pack make?
One 32 oz pack treats approximately 20 gallons of water. That's enough for one barrel fill at the 20-gallon level. Depending on your foam machine and output level, one barrel of solution can produce foam for roughly 15–45 minutes of operation.

Do I need to measure anything?
No. Pour the entire pack into your barrel, then fill with water to approximately 20 gallons. The pack is premixed at the correct concentration — the full 32 oz into 20 gallons produces the right solution strength. No measuring cups, no calculators, no ratio charts.

Is this the same foam as Ready to Run or Gel?
Same chemistry, same foam quality. Pour & Go uses the same cosmetic-grade surfactant blend as every SurgeFX foam solution. The difference is packaging and convenience — Pour & Go is sized and premixed so you never have to think about ratios. The foam your machine produces is identical to what it would produce with any other SurgeFX solution format.

How many packs do I need for a party?
That depends on your event size and duration. Each pack fills one 20-gallon barrel of solution. A short backyard party running one machine for under an hour may only need 1–2 packs. A 2–3 hour party running continuously could go through 3–5 packs depending on output. For events expecting to use more than 3 barrels, consider stepping up to Ready to Run (1 Gallon) for better per-gallon economics.

Can I use two packs in one barrel for stronger foam?
You can, but it's not recommended. One pack per 20 gallons is the calibrated concentration. Over-concentrating can produce foam that's too dense, breaks down unevenly, or causes excess buildup in your pump and lines. If you want denser foam, use one pack with slightly less water (15 gallons instead of 20) rather than doubling the concentrate.

Is it safe?
Yes. Same safety profile as all SurgeFX foam solutions — hypoallergenic, neutral pH, biodegradable, non-staining. No cleaning chemicals, detergents, dyes, or artificial fragrances. Safe for direct skin contact in adults, children, and pets. Avoid direct eye contact; rinse with clean water if foam contacts eyes.

Can I add colorant or UV powder?
Yes. Pour the pack into your barrel, fill with water, then add Foam Color Additive or UV Glow Powder and stir to distribute. Add additives to the mixed solution, never to the pack itself.

Works with all foam machines?
Yes. Once mixed into water, the solution works with the Foam Blaster Maxx, Foam Blaster Pro-X, the Black Box, and any standard foam machine that draws from a solution barrel.

Does it expire?
Sealed packs have an extended shelf life. Once mixed with water in your barrel, use the solution within 24–48 hours for best results. Keep sealed packs stored at room temperature away from extreme heat or freezing.

Why not just buy the gallon of Ready to Run?
If you're running multiple barrels or regular events, you should — Ready to Run (1 Gallon) is significantly more cost-effective at volume. Pour & Go exists for buyers who want zero-complexity mixing for a single event, for rental operators sending solution with inexperienced clients, and for anyone who values "pour the whole thing in and go" simplicity over per-gallon economics.

Can I use this with the Black Box?
Yes. Pour the pack into an external solution container and connect the Black Box pickup hoses. The Black Box will draw from the solution and blend inline as normal. However, for regular Black Box use, Ready to Run in the gallon size is more practical and cost-effective.

💡 Pro Tips

Less Water = Denser Foam
If you want thicker, denser foam, use slightly less water — 15 gallons instead of 20. The concentrate is slightly more concentrated at that volume, producing heavier, stacking foam. Don't go below 15 gallons per pack — too concentrated and you waste solution without improving foam quality.

Perfect for Rental Add-Ons
If you rent out foam machines, include Pour & Go Packs with each rental instead of explaining mixing ratios. Your client pours the pack in, fills with water, and runs the machine. No support calls about measurements. No complaints about weak foam from incorrect mixing. Sell the packs as an add-on and eliminate the customer's biggest source of confusion.

Keep a Few in Your Gear Case
Even if you normally use Ready to Run or Gel, stashing 2–3 Pour & Go Packs in your equipment case gives you instant emergency backup. If you run through solution faster than expected, burn a barrel on a test run, or discover a mixing problem on-site, a Pour & Go Pack gets you 20 gallons of solution in under a minute with zero measuring.

Pour First, Then Fill
Always pour the pack into the barrel before adding water — not the other way around. Pouring the concentrate into incoming water helps it disperse naturally as the barrel fills. If you add the pack on top of a full barrel, you'll need to stir to distribute the concentrate sitting on the surface.

Mark the 20-Gallon Line on Your Barrel
If you're using a standard 53-gallon barrel, mark the 20-gallon level with tape or a marker. That's roughly 40% full — not quite halfway. Having the line marked means you don't have to estimate every time you fill. Fill to the line, pour in a pack, and go.

Great for Testing New Machines
Just bought a new foam machine and want to test it before your first event? A single Pour & Go Pack gives you a quick 20-gallon barrel to run a test without opening your bulk solution supply. Test your output, verify your pump works, check for leaks, then dump the test batch and load fresh solution for the actual event.